This shows you the differences between two versions of the page.
software:knowledge-base:brand-knowledge-base:global-cache [2015/01/07 02:49] jarrod [Adding The System in guiDesigner] |
software:knowledge-base:brand-knowledge-base:global-cache [2015/01/07 02:51] (current) jarrod [Relay Commands] |
||
---|---|---|---|
Line 21: | Line 21: | ||
==== Infrared (IR) Commands ==== | ==== Infrared (IR) Commands ==== | ||
IR commands send to Global Cache hardware must be in a specific format as shown below | IR commands send to Global Cache hardware must be in a specific format as shown below | ||
- | ^sendir,<connectoraddress>,<ID>,<frequency>,<repeat>,<offset>,<on1>,<off1>,<on2>,<off2>,….,<onN>,<offN>^ (where N is less than 260 or a total of 520 numbers) | + | ^sendir,<connectoraddress>,<ID>,<frequency>,<repeat>,<offset>,<on1>,<off1>,<on2>,<off2>,….,<onN>,<offN>\x0D^ (where N is less than 260 or a total of 520 numbers) |
where; | where; | ||
Line 32: | Line 32: | ||
**<on1>** is |1|2|…|65635| (4) (number of pulses)\\ | **<on1>** is |1|2|…|65635| (4) (number of pulses)\\ | ||
**<off1>** is |1|2|…|65635| (4) (absence of pulse periods of the carrier frequency)\\ | **<off1>** is |1|2|…|65635| (4) (absence of pulse periods of the carrier frequency)\\ | ||
- | + | **\x0D** is a carriage return which must be appended to all commands sent to Global Cache units from iViewer. | |
- | An example of an IR Command in Globacl Cache Format looks like this:\\ | + | An example of an IR Command in Global Cache Format looks like this:\\ |
- | ^sendir,1:1,1,38109,1,1,171,171,21,64,21,64,21,64,21,21,21,21,21,21,21,21,21,21,21,64,21,64,21,64,21,21,21,21,21,21,21,21,21,21,21,21,21,64,21,64,21,21,21,21,21,21,21,21,21,21,21,64,21,21,21,21,21,64,21,64,21,64,21,64,21,64,21,3810 ^ | + | ^sendir,1:1,1,38109,1,1,171,171,21,64,21,64,21,64,21,21,21,21,21,21,21,21,21,21,21,64,21,64,21,64,21,21,21,21,21,21,21,21,21,21,21,21,21,64,21,64,21,21,21,21,21,21,21,21,21,21,21,64,21,21,21,21,21,64,21,64,21,64,21,64,21,64,21,3810\x0D ^ |
To learn your IR code in Global Cache format, you will need to use their [[http://www.globalcache.com/downloads/|iLearn software]] (if you have a Global Cache IR Learner). Or use their [[http://www.globalcache.com/downloads/|iConvert software]] to convert hex (CCF) to Global Cache IR format. | To learn your IR code in Global Cache format, you will need to use their [[http://www.globalcache.com/downloads/|iLearn software]] (if you have a Global Cache IR Learner). Or use their [[http://www.globalcache.com/downloads/|iConvert software]] to convert hex (CCF) to Global Cache IR format. | ||
Line 45: | Line 45: | ||
Relay state is set as follows:\\ | Relay state is set as follows:\\ | ||
- | setstate,1:1,<outputstate> for the 1st relay output\\ | + | setstate,1:1,<outputstate>\x0D for the 1st relay output\\ |
- | setstate,1:2,<outputstate> for the 2nd relay output\\ | + | setstate,1:2,<outputstate>\x0D for the 2nd relay output\\ |
- | setstate,1:3,<outputstate> for the 3rd relay output\\ | + | setstate,1:3,<outputstate>\x0D for the 3rd relay output\\ |