You can find the results of your search below. If you didn't find what you were looking for, you can create or edit the page named after your query with the appropriate tool.
====== On-BoardRS232PortProtocol ======
This document defines the CFLink protocol for working with the on-board serial po... n ====
The ''SPC'' query requests the current on-boardRS232port settings of a device.
=== Data ===
The ''SPC'' ... Only required if the device has more than one on-boardRS232port, such as the [[hardware:solo|Solo]].
* **<MODE>... ===
<sxh cflink; light: true>
// Configure the on-board serial port for a LAN Bridge on ID [02] to be in RS232 mode, 9600 baud, 8:None:1.
> [F2][02][F3]CLANSPC[
ages.\\
Note that the Solo does NOT feature an on-board CFLink port, but it still uses the same protocol for communication over Ethernet.
By default, the... for which documentation is available in the [[on-board-rs232-port-protocol|On-BoardRS232 docs]].
===== Queries =====
==== WHO - Device d... ntact input port names
* ''COM'' = Query the on-boardRS232port names
* ''IRX'' = Query the on-board IR port na... ngs for the on-board serial ports.\\
For the 2 on-board bi-directional RS232 ports, follow the protocol documentation for [[hardware:cflink:on-board-rs23
* COM Port Program Mode (Amber)
* Solid = On-boardRS232port is in Program Mode (for communicating with CFLink... RS232).
* COM PortRS232 Mode
* Solid = On-boardRS232port is in RS232 Mode (for controlling third part RS232 devices).
... d Buttons ====
* Setup
* Press to toggle on-boardRS232 Mode
* Reset
* Press to reset the unit. See... Port 8 +
- Port 8 -
==== RS232 ====
The RJ12 port is used to communicate to and from RS232 devices.\\
Depending what mode the RS232port is
rotocol messages.\\
The LAN Bridge also has an on-boardRS232port, for which documentation is available in the [[on-board-rs232-port-protocol|On-BoardRS232 docs]].
===== Common Definitions =====
The following communication slots exist o... his command is not to be used to send data to the RS232 slot (Slot 1), instead use the [[on-board-rs232-port-protocol|''SPW'' Command]] common to all devices with an on-boardRS232port.\\
=== Data ===
<sxh cflink; light: true>
> [F2]
tocol =====
Although the Solo does not have an on-board CFLink port, it still shares the same protocol for communication and control.\\
Use the CFLink p... data being sent or received via the associated on-boardRS232port.
* Off = No RS232 data being sent/received.
... mbered 1, 2, 3 and 4)
* Solid = Associated on-board dry contact port is closed.
* Off = Associated dry contact port is open.
==== Pinhole Buttons ====
* Setup
* Used in combination with res
* COM Port Program Mode (Amber)
* Solid = On-boardRS232port is in Program Mode (for communicating with CFLink... RS232).
* COM PortRS232 Mode
* Solid = On-boardRS232port is in RS232 Mode (for controlling third part RS232 devices).
... e Buttons ====
* Setup
* Press to toggle on-boardRS232 Mode
* Reset
* Press to reset the unit. See... rt **10207**''.
</WRAP>
==== RS232 ====
The RJ12 port is used to communicate to and from RS232 devices.\\
Depending what mode the RS232port is
ing the command, such as for [[hardware:cflink:on-board-rs232-port-protocol|on-board COM ports]] which share a common protoco... nd replies.
==== Port Definitions ====
When the protocol requires a port number to be defined, it is always written in P##... umber must be two chars, 01-99 or ZZ.\\
''P01'' = Port 1, ''P10'' = Port 10, etc.\\
''PZZ'' = All Ports.... CF Mini.
==== Module Definitions ====
When the protocol requires a module number to be defined, it is alw
ions with any device with an [[hardware:cflink:on-board-rs232-port-protocol|on-boardRS232port]].
{{ :software:system-commander:automatic_discov... r LAN.
===== RS232 Discovery =====
Using the on-boardRS232port of any device, you can detect the device itself, ... ink device connected to it.
First, make sure the RS232port is in 'Program Mode'. This is done by pressing a ... g on what device you are using).
Now connect the RS232port on the device to a COM Port on your computer. If your computer does not have
done with any CommandFusion device that has an on-boardRS232port.\\
{{ :software:system-commander:automatic_discov... ece of hardware you are using. Now we connect the RS232port on the device to the COM port on your computer. If you don't have any COM ports available, then you can use a third party RS232 to USB adapter.\\
{{ :software:system-commander:commandfusion_rs232_auto_discovery.png?direct&700 |}}
\\
In System Commander, choose ''Network'', the
or codes are common across all devices with an on-boardRS232port.
* 075 = Invalid COM Settings
* 076 = Invali... = Invalid Slot IP Address
* 119 = Invalid Slot Port Number
* 120 = Invalid Slot Timeout
* 121 = I... ===== 350 - 399: COM Error Codes =====
* 350 = Port P03/P04 cannot be 485H or 4XXF if P01/P02 is not ... t 232.
* 353 = Buffer is full
* 354 = Invalid Port Write. Port is in OFF mode.
===== 400 - 424: Rel
ber and firmware version.\\
\\
Devices with an on-board serial port will allow you to setup the communication settings for the RS232 serial port.\\
\\
The LAN Bridge will also show options specific to the Ethernet con... g?direct&600 |}}
For IR ports, you can choose the port and format of IR data to test, including the on-board database which has a wizard built in to find the right command. Pressing the send button will se
target device in our example case will be the on-boardRS232port of the LAN Bridge. Then enter the RS232 command we want to send and press ''OK''. \\
{{ :software:system-commander:quick-start-guide:syste... n our example case, this is done by pulsing relay port 1 of a CF Mini to close for 1 second. So choose t... n type and ''CF Mini'' target device, then select port 1 and set it to pulse for 1 second.\\
<WRAP cente
nputs. 1 x detachable 3-pin 3.5mm terminal block.
RS232 - Serial port for control. 1 x detachable 3-pin 3.5mm terminal ... USB using PC software. Can also be programmed via RS232 or RS485 connection (either directly or via Ether... r).
Power - 1 x blue LED indicating power status.
RS232 - 1 x yellow LED indicating RS232 serial traffic.