CommandFusion Wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== On-Board RS232 Port Protocol ======

This document defines the CFLink protocol for working with the on-board serial port found on the following CommandFusion hardware models:
  * [[hardware:lan-bridge|LANBridge]] (RJ11)
  * [[hardware:cf-mini|CFMini]] (RJ11)
  * [[hardware:modular-base-units:din-mod4|DIN-MOD4]] (DB9 Female)
  * [[hardware:modular-base-units:mod4|MOD4]] (DB9 Female)

===== Queries =====

==== SPC - Query Serial Port Configuration ====

The ''SPC'' query requests the current on-board RS232 port settings of a device.

=== Data ===

The ''SPC'' query does not have any associated data.

=== Reply ===
<sxh cflink; light: true>
< [F2]<ID>[F3]RCFXSPC[F4]<MODE>:<BAUD>:<DATABITS>:<PARITY>:<STOP>:<FLOWCTRL>[F5][F5]
</sxh>

See the ''SPC'' command for details on each returned data parameter.

=== Example ===
<sxh cflink; light: true>
// Query the Serial Port configuration of a LANBridge on ID [02]
> [F2][02][F3]QLANSPC[F4][F5][F5]
// Reply with the configuration data, Serial Port is in Program mode
< [F2][02][F3]RLANSPC[F4]PGM:115200:8:N:1:0[F5][F5]
</sxh>

===== Configuration Messages =====

==== SPC - Serial Port Configuration ====

The ''SPC'' (Serial Port Configuration) command is used to configure the properties of the serial port such as Port Mode, Baud rate, Flow Control, etc.

=== Data ===
<sxh cflink; light: true>
> [F2]<ID>[F3]CCFXSPC[F4]<MODE>:<BAUD>:<DATABITS>:<PARITY>:<STOPBITS>:<FLOWCTRL>[F5][F5]
</sxh>

  * **<MODE>** = The mode of the RS232 port:
    * ''PGM'' (Program Mode) means incoming data must be valid CFLink formatted commands, and allows you to send data to any device on the CFLink network via RS232. All CFLink data received by the device will also be sent out the RS232 port in this mode.
    * ''232'' (RS232 Mode) means incoming data is sent only to devices that are configured via the TGT command. The incoming RS232 data will be wrapped in a SPR reply before being sent to the target devices. Data is sent to the RS232 port using the SPW command when in this mode.
  * **<BAUD>** = The baud rate of the RS232 port:
    * 100
    * 300
    * 600
    * 1200
    * 2400
    * 4800
    * 9600
    * 14400
    * 19200
    * 38400
    * 57600
    * 115200 (Default Program Mode baud rate)
    * 128000
    * 256000
  * **<DATABITS>** = The data bits of the RS232 port, always 8.
  * **<PARITY>** = The parity of the RS232 port (single uppercase char):
    * ''N'' = None
    * ''O'' = Odd
    * ''E'' = Even
  * **<STOPBITS>** = The stop bits of the RS232 port (''1'' or ''2'').
  * **<FLOWCONTROL>** = The flow control of the RS232 port (''0'' = None, ''1'' = RTS/CTS).

=== Reply ===
<sxh cflink; light: true>
< [F2]<ID>[F3]RCFXSPC[F4]<MODE>:<BAUD>:<DATABITS>:<PARITY>:<STOP>:<FLOWCTRL>[F5][F5]
</sxh>

=== Example ===
<sxh cflink; light: true>
// Configure the on-board serial port for a LANBridge on ID [02] to be in RS232 mode, 9600 baud, 8:None:1.
> [F2][02][F3]CLANSPC[F4]232:9600:8:N:1:0[F5][F5]
// Reply
< [F2][02][F3]RLANSPC[F4]232:9600:8:N:1:0[F5][F5]
</sxh>

=== Error ===

  * 050 = Invalid COM Mode


==== TGT - Configure Notifications Targets ====

The ''TGT'' command configures which CFLink ID's on the CFLink network will receive incoming messages when data is received on the serial port whilst in RS232 mode ''232''.\\
If the serial port is in Programming Mode ''PGM'', then this configuration is ignored, no data is sent to the target devices. Instead all incoming data is handled by the device with the Serial Port, and must be a valid CFLink message or it will be ignored.

=== Data ===
<code>
> [F2]<ID>[F3]CCFXTGT[F4]<ID1>:<ID2>:<ID3>:<ID4>:<ID5>[F5][F5]
</code>
**<ID1-5>** = The target CFLink ID to forward incoming serial port data to. Use the No Change Option ''XX'' to leave a specific ID unchanged. The ID's should be in plain text format, 2 chars (A-F, 0-9).

=== Reply ===
<code>
< [F2]<ID>[F3]RCFXTGT[F4]<ID1>:<ID2>:<ID3>:<ID4>:<ID5>[F5][F5]
</code>
=== Example ===
<code>
// Forward incoming data from the Serial Port on LANBridge ID [02] to devices on CFLink ID's [03], [04] and [05]
> [F2][02][F3]CLANTGT[F4]03:04:05:XX:XX[F5][F5]
// Reply (CFLink ID's [07] and [09] were already being targeted from an earlier configuration)
< [F2][02][F3]RLANTGT[F4]03:04:05:07:09[F5][F5]
</code>
=== Error ===
  * 051 = Invalid COM Targets

===== Transmission Messages =====

==== SPW - Serial Port Write ====

The ''SPW'' (Serial Port Write) command is used to write data to a device connected to the on-board serial port.
This command is ignored in PGM mode.

=== Data ===
<code>
> [F2]<ID>[F3]TCFXSPW[F4]<DATA>[F5][F5]
</code>

**<DATA>** = The data to be written out the on-board serial port. Hex bytes must be entered in \xFF format. eg. A carriage return is written as \x0D

=== Reply ===
<code>
// In an effort to reduce network traffic, the reply does not contain the data sent.
< [F2]<ID>[F3]RCFXSPW[F4][F5][F5]
</code>

=== Example ===
<code>
// Send a command out the on-board serial port of a CFMini on CFLink ID [03]
> [F2][03][F3]TMINSPW[F4]Hello World!\x0D[F5][F5]
// Reply
< [F2][03][F3]RMINSPW[F4][F5][F5]
</code>

=== Error ===

  * 052 = COM Buffer Overflow

===== Notifications =====

==== SPR - Serial Port Read ====

The ''SPR'' notification contains incoming serial data, received from the on-board RS232 port when in RS232 Mode ''232''.\\
The reply is only sent to the CFLink ID's configured via the ''TGT'' command. This reply is never generated when serial port is in Program Mode ''PGM''.

=== Data ===
<code>
< [F2]<ID>[F3]R<DEVICE>SPR[F4]<DATA>[F5][F5]
</code>

=== Example ===
<code>
// An incoming message "Hello World!" followed by a carriage return is received on the on-board serial port of a CFMini on CFLink ID [03].
// The CFMini is configured to send incoming RS232 data to CFLink ID's [02], [04] and [07]
< [F2][02][F3]RMINSPR[F4]Hello World!\x0D[F5][F5]
< [F2][04][F3]RMINSPR[F4]Hello World!\x0D[F5][F5]
< [F2][07][F3]RMINSPR[F4]Hello World!\x0D[F5][F5]
</code>
CommandFusion Wiki

User Tools

Site Tools

Page Tools
