User Tools
hardware:cflink:cflink-introduction
Differences
This shows you the differences between two versions of the page.
|
hardware:cflink:cflink-introduction [2012/10/18 02:37] jarrod [Data Separator] |
hardware:cflink:cflink-introduction [2014/02/20 11:57] (current) jarrod [Commands and Replies] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== CFLink Protocol Introduction ====== | ====== CFLink Protocol Introduction ====== | ||
| This document is an overall view of the CFLink Protocol, used by CommandFusion hardware.\\ | This document is an overall view of the CFLink Protocol, used by CommandFusion hardware.\\ | ||
| - | CFLink is a RS485 5-wire bus, used to interconnect various CommandFusion devices. For more details on the physical bus characteristics, please see the [[hardware:cflink:cflink-bus|CFLink Bus documentation]].\\ | + | CFLink is an RS485 5-wire bus, used to interconnect various CommandFusion devices. For more details on the physical bus characteristics, please see the [[hardware:cflink:cflink-bus|CFLink Bus documentation]].\\ |
| ===== Basic Structure ===== | ===== Basic Structure ===== | ||
| Line 21: | Line 21: | ||
| Then an ''[F4]'' byte, followed by optional Data associated with the command. The Data can be empty if the command does not require any associated data.\\ | Then an ''[F4]'' byte, followed by optional Data associated with the command. The Data can be empty if the command does not require any associated data.\\ | ||
| Finally, all messages are terminated with two ''[F5]'' bytes.\\ | Finally, all messages are terminated with two ''[F5]'' bytes.\\ | ||
| - | \\ | + | |
| - | **NOTE: THROUGHOUT THIS DOCUMENTATION, ALL CFLINK EXAMPLES WILL START WITH > OR < - THIS IS NOT PART OF THE COMMAND, BUT JUST USED TO SIGNIFY THE START OF A NEW SENT OR RECEIVED PACKET.** | + | <WRAP center round important 80%> |
| + | **NOTE: THROUGHOUT THIS DOCUMENTATION, ALL CFLINK EXAMPLES WILL START WITH ''>'' (greater than) OR ''<'' (less than) - THIS IS NOT PART OF THE COMMAND, BUT JUST USED TO SIGNIFY THE START OF A NEW SENT OR RECEIVED PACKET WITHIN THE DOCUMENTATION.** | ||
| + | </WRAP> | ||
| ===== CFLink ID ===== | ===== CFLink ID ===== | ||
| Line 33: | Line 35: | ||
| In some circumstances, you may want to send a broadcast to all devices on the network. This can be done by using the Broadcast ID: ''[FF]''. | In some circumstances, you may want to send a broadcast to all devices on the network. This can be done by using the Broadcast ID: ''[FF]''. | ||
| + | <WRAP center round important 80%> | ||
| **NOTE: BROADCAST MESSAGES CANNOT BE GUARANTEED TO BE DELIVERED TO ALL DEVICES ON LARGE NETWORKS. BROADCASTING IS ONLY RECOMMENDED FOR NON-CRITICAL MESSAGES.** | **NOTE: BROADCAST MESSAGES CANNOT BE GUARANTEED TO BE DELIVERED TO ALL DEVICES ON LARGE NETWORKS. BROADCASTING IS ONLY RECOMMENDED FOR NON-CRITICAL MESSAGES.** | ||
| + | </WRAP> | ||
| ===== Commands and Replies ===== | ===== Commands and Replies ===== | ||
| The **<COMMAND>** part of each message is always 7 characters, always upper case, and formatted as follows: ''<TYPE><DEVICE><COMMAND_NAME>''\\ | The **<COMMAND>** part of each message is always 7 characters, always upper case, and formatted as follows: ''<TYPE><DEVICE><COMMAND_NAME>''\\ | ||
| Line 40: | Line 43: | ||
| * **<TYPE>** = 1 char, types are documented below.\\ | * **<TYPE>** = 1 char, types are documented below.\\ | ||
| * **<DEVICE>** = 3 chars representing the model name of the device or type of port we are targeting (or the device/port type that the reply came from).\\ | * **<DEVICE>** = 3 chars representing the model name of the device or type of port we are targeting (or the device/port type that the reply came from).\\ | ||
| - | * The **<DEVICE>** name ''CFX'' can be used to target any device. It is useful for when you are sending a command that any device should respond to, ''WHO'' for example.\\ | + | * The **<DEVICE>** name ''CFX'' can be used to target any device. It is very useful for when you are sending a command that any device should respond to, ''WHO'' for example.\\ It is also useful when you don't need to know the exact device type receiving the command, such as for [[hardware:cflink:on-board-rs232-port-protocol|on-board COM ports]] which share a common protocol across all devices.\\ However, all //replies/notifications// will be sent with the correct 3 character device identifier for the device sending the data (''CFX'' is never used in replies except from bootloader notifications). |
| * **<COMMAND_NAME>** = 3 chars representing the name of the actual command being performed. | * **<COMMAND_NAME>** = 3 chars representing the name of the actual command being performed. | ||
| - | |||
| ==== Queries ==== | ==== Queries ==== | ||
| Line 108: | Line 110: | ||
| When the protocol requires a port number to be defined, it is always written in P## format. The number must be two chars, 01-99 or ZZ.\\ | When the protocol requires a port number to be defined, it is always written in P## format. The number must be two chars, 01-99 or ZZ.\\ | ||
| ''P01'' = Port 1, ''P10'' = Port 10, etc.\\ | ''P01'' = Port 1, ''P10'' = Port 10, etc.\\ | ||
| - | ''PZZ'' = All Ports. This allows you to manipulate all ports of a single type at once. eg. Open all relays in a CFMini. | + | ''PZZ'' = All Ports. This allows you to manipulate all ports of a single type at once. eg. Open all relays in a CF Mini. |
| ==== Module Definitions ==== | ==== Module Definitions ==== | ||
| Line 138: | Line 140: | ||
| // Port Separator example - Close relay port 1, open relay port 2 on a CF Mini on CFLink ID [04] | // Port Separator example - Close relay port 1, open relay port 2 on a CF Mini on CFLink ID [04] | ||
| > [F2][04][F3]TRLYSET[F4]P01:1|P02:0[F5][F5] | > [F2][04][F3]TRLYSET[F4]P01:1|P02:0[F5][F5] | ||
| - | // Port Separator example, with module number - Close relay port 1, open relay port 2 on Module 2 of a MOD4 on CFLink ID [04]> [F2][04][F3]TRLYSET[F4]M2|P01:1|P02:0[F5][F5] | + | // Port Separator example, with module number - Close relay port 1, open relay port 2 on Module 2 of a MOD4 on CFLink ID [04] |
| + | > [F2][04][F3]TRLYSET[F4]M2|P01:1|P02:0[F5][F5] | ||
| </sxh> | </sxh> | ||
| ==== Data Separator ==== | ==== Data Separator ==== | ||
| - | The data separator '':'' (colon), is used to separate piece of data for a single target port or device.\\ | + | The data separator '':'' (colon), is used to separate pieces of data for a single target port or device.\\ |
| <sxh cflink; light: true> | <sxh cflink; light: true> | ||
| // Data Separator example - Device discovery reply for a LAN Bridge on ID [02] | // Data Separator example - Device discovery reply for a LAN Bridge on ID [02] | ||
hardware/cflink/cflink-introduction.1350527842.txt.gz · Last modified: 2012/10/18 02:37 by jarrod
